DELTA PRO 12

* Kapton coil former for increased rigidity and thermal protection * Polyamide-imide coated two-layer, 28ga/., copper voice coil for improved power-handling and durability * Ferrite Magnet * Vented and exteded core for increased power-handling * Die-cast aluminum basket for rigidity * Rolled cloth cone edge with deep corrugations for exteneded Xmax * Solid composition paper dust cap

Nominal Basket Diameter - 12", 304.8mm Impedance - 8 ohms Power Rating - 400Wrms Resonance - 51Hz Usable Frequency Range - 50Hz-5kHz Magnet Weight - 80oz Gap Height - 0.375", 9.52mm Voice Coil Diameter - 2.5", 63.5mm

WEIGHT:18.1LBS

COMPRESSION DRIVER PSD:2002S

* 16 ohms

COMPRESSION DRIVER PSD:2002

KAPPA PRO 12

Performance optimized for sound reinforcement systems. Also suitable for bass guitar, keyboards, club music systems, and stage monitors.

* Kapton coil former for increased rigidity and thermal protection * Polyamide-imide coated two-layer, 27ga., copper voice coil for improved power-handling and durability * Ferrite Magnet * Vented and extended core for increased power-handling * Die-cast aluminum basket for rigidity * Paper cone * Cloth cone edge * Solid composition paper dust cap * Nominal Basket Diameter 12", 304.8mm * Impedance 8ohms * Power Rating 500Wrms * Resonance 37Hz * Usable Frequency Range 35Hz-2.5kHz * Magnet Weight 80oz * Gap Height 0.375", 9.52mm * Voice Coil Diameter 3.0", 76.2mm

SHIPPING WEIGHT:18.8LBS

LEGEND B102

The best Eminence all-purpose, broad bandwidth, bass guitar speaker! This unit exhibits lots of punch and is great for Pop and Slap BASS, Jazz and Rock'n'Roll. The efficiency of the whizzer cone eliminates the need for a tweeter. This speaker is an ideal replacement or upgrade for bass players.

* Impedance - 8 ohms * Power Rating - 200Wrms * Voice Coil Diameter 2", 50.8mm * Coil Material - Copper * Flat/Round Coil Wire - Round * Coil Former Material - KAPTON * Basket Type - Cast * Cone Surround Material - Cloth * Dust Cap Material - Paper * Magnet Weight - 45oz * Usable Bandwidth - 40Hz- 9kHz * SPL - 95dB

WEIGHT: 12.0LBS

KAPPA PRO 15

* Kapton coil former for increased rigidity and thermal protection * Polyamide-imide coated two-layer , 27ga., aluminum voice coil for lower mass and increased sensitivity * Ferrite Magnet * Vented and extended core for increased power-handling * Die-cast aluminum basket for rigidity * Paper cone * Cloth cone edge * Solid composition paper dust cap

Nominal Basket Diameter - 15", 381mm Impedance - 8 ohms Power Rating - 500Wrms Resonance - 47Hz Usable Frequency Range - 40Hz-4kHz Magnet Weight - 80oz Gap Height - 0.375", 9.52mm Voice Coil Diameter - 3.0", 76.2mm

WEIGHT:20.00 LBS

DELTA 10

* Kapton coil former for increased rigidity and thermal protection * Polyamide-imide coated one-layer, 28ga., aluminum voice coil for lowest possible mass and maximum sensitivity * Ferrite Magnet * Vented core for increased power handling * Premium pressed steel basket for maximum strength * Paper cone * Rolled cloth cone edge * Solid composition paper dust cap

Nominal Basket Diameter - 10", 254mm Impedance - 8ohms or 16 ohms Power Rating -350Wrms Resonance - 66Hz Usable Frequency Range - 65Hz - 3.5kHz Magnet Weight - 56oz Gap Height - 0.375", 9.52mm Voice Coil Diameter - 2.5:, 63.5mm

WEIGHT:12.2LBS

BETA 15: FOR ALL HIGH POWER BASS APPLICATIONS INCLUDING BASS GUITAR

* Kapton coil former for increased rigidity and thermal protection * Polyamide-imide coated two-layer, 30ga., copper voice coil for improved power handling and durability. * Ferrite Magnet * Vented core for increased power handling * Premium pressed steel basket for maximum strengh * Paper cone * Cloth cone edge * Solid composition paper dust cap

Nominal Basket Diameter - 15", 381mm Impedance - 4 ohms or 8 ohms Power Rating - 350Wrms Resonance - 35 HZ Usable Frequency Range - 35Hz - 4kHz Magnet Weight - 34oz Gap Height 0.312", 7.94mm Voice Coil Diameter 2", 50.8mm

WEIGHT: 11LBS

PX SERIES: pxb3:3k5 PROFESSIONAL CROSSOVERS

Designed to work in high-power cabinets, px crossovers are technically superior passive filters available as board-only or complete with fitted hardware for a smart, economical 'factory-fit' finish.

Designed and built for Eminence, px crossovers feature advanced circuit design to both preserve the crossover and your HF drivers.

A common crossover problem in L-PAD failure brought about by winding burnout when maximum attenuation is prolonged.

Full attenuation concentrates the maximum voltage drop in a small winding area-a potentially damaging state even with high-power L-PAD devices.

In px crossovers, current is limited when the hf level control is set to "0" on its scale (max. -9dB attenuation). A secondary benefit of the design is to form a voltage divider across the JF driver. The High-Pass Protection uses custom-built aerospace lamps as positive temperature coefficient series varistors.

The tungsten filaments effectively track the program material, dynamically maintaining a safe maximum current level to the HF driver without introducing distortion. This circuitry provides smooth 3:1 analog compression during input overload conditions over 250Wrms. At full drive level approaching clipping, the electrical attenuation to the protected JF driver is -4.5dB. In every way, Eminence px crossovers are technically superior product.

* Type 3-Way * Crossover Frequency 500Hz/3.5kHz * 12dB/octave LP - 6dB/octave MP - 18dB/octave HP Butterworth * Impedance 8ohms * Power Handling 400Wrms

PX SERIES:PXB2:800 PROFESSIONAL CROSSOVERS

Designed to work in high-power cabinets, px crooovers are technically superior passive filters available as board-only or complete with fitted hardware for a smart, economical 'factory-fit' finish.

Designed and buit for Eminence, px crossovers feature advanced circuit design to both preserve the crossover and your HF drivers.

A common crossover problem in L-PAD failure brought about by winding burnout when maximum attenuation is prolonged.

Full attenuation concentrates the maximum voltage drop in a small winding area - a potentially damaging even with high-power L-PAD devices.

In px crossovers, current is limited when the hf level control is set to "0" on its scale (max. -9dB attenuation). A secondary benefit of the design is to form a voltage divider across the HF driver. The High-Pass Protection uses custom-built aerospace lamps as positive temperature coefficient series varistors.

The tungsten filaments effectively track the program material, dynamically maintaining a safe maximum current level to the HF driver without introducing distortion. This circuitry provides smooth 3:1 analog compression during input overload conditions over 250Wrams. At full drive level approaching clipping, the electrical attenuation to the protected HF driver is -4.5dB. In every way, Eminence px crossovers are a technically superior product.

* 2-Way * Crossover Frequency 800Hz * 12dB/octave LP - 18dB/octave HP Butterworth * Impedance 8ohms * Power Handling 400Wrms

PX SERIES:PXB:1k6 PROFESSIONAL CROSSOVERS

Designed to work in high-power cabinets, px crossovers are technically superior passive filters available as board-only or complete with fitted hardware for a smart, economical 'factor-fit' finish.

Designed and built for Eminence, px crossovers feature advanced circuit design to both preserve the crossover and your HF drivers.

A common crossover problem in L-PAD failure brought about by winding burnout when maximum attenuation is prolonged.

Full attenueation concentrates the maximum voltage drop in a small winding area-a potentially damaging state even with high-power L-PAD devices.

In px crossovers, current is limited when the HF level control is set to "0" on its scale (max. -9dB attenuation). A secondary benefit of the design is to form a voltage divider across the HF driver. The High-Pass Protection uses custom-built aerospace lamps as positive temperature coefficient series varistors.

The tungsten filaments effectively track the program material, dynamically maintaining a safe maximum current level to the HF driver without introducing distortion. This circuitry provides smooth 3:1 analog compression during input overload conditions over 250Wrms. At full drive level approaching clipping, the electrical attenuation to the protected HF driver is -4.5dB. In every way, Eminence px crossovers are a technically superior product.

* High-Pass * Crossover Frequency 1.6kHz * 18dB/octave Butterworth * Impedance 8ohms * Power handling 400Wrms

DELTA PRO 15

* Kapton coil former for increased rigidity and thermal protection * Polyamide coated two-layer, 28ga., copper voice coil for improved power-handling and durability * Ferrit Magnet * Vented and extended core for increased power-handling * Die-cast aluminum basket for rigidity * Paper cone * Rolled cloth cone edge with deep corrugations for extended Xmax * Solid composition paper dust cap

Nominal Basket Diameter - 15", 381mm Impedance - 8ohms Power Rating - 400Wrms Resonance - 42Hz Usable Frequency Range 40HZ - 4kHz Magnet Weight - 80oz Gap Height - 0.375", 9.52mm Voice Coil Diameter - 2.5", 63.5mm

WEIGHT:19.8LBS

BETA 12: FOR ALL HIGH POWER BASS APPLICATIONS INCLUDING BASS GUITAR

* Kapton coil former for increased rigidity and thermal protection * Polyamide-imide coated two-layer, 32ga., copper voice coil for improved power handling and durabilily. * Ferrite Magnet * Vented core for increased power handling * Premium pressed steel basket for maximum strength * Paper cone * Cloth cone edge * Solid composition paper dust cap

Nominal Basket Diameter - 12", 304.8mm Impedance - 8 ohms or 16 ohms Power Rating - 250Wrms Resonance - 50Hz Usable Frequency Range - 50Hz - 5kHz Magnet Weight - 34oz Gap Height - 0.312", 7.94mm Voice Coil Diameter - 2", 50.8mm

WEIGHT:8.2LBS

DIAPHRAM PSD202-16

* Diaphragm Material - Titanium * Diaphragm for 2002 driver

PX SERIES:PXB2:1k6 PROFESSIONAL CROSSOVERS

Designed to work in high-power cabinets, px crossovers are technically superior passive filters available is board-only or complete with fitted hardware for a smart, economical 'factory-fit' finish.

Designed and built for Eminenece, px crossovers feature advanced circuit design to both preserve the crossover and your HF drivers.

A common crossover problem in L-PAD failure brought about by winding burnout when maximum attenuation is prolonged.

Full attenuation concentrates thae maximum voltage drop in a small winding area - a potentially damaging state even with high-power L-PAD devices.

In px crossovers, current is limited when the jf level control is set to "0" on its scale (max. -9dB attenuation). A secondary benefit of the design is to form a voltage divider across the HF driver. The High-Pass Protection uses cutom-built aerospace lamps as positive temperature coefficient series varistors.

The tungsten filamemts effectively track the program material, dynamically maintaining a safe maximum current level to the HF driver without introducing distortion. This circuitry provides smooth 3:1 analog compression during input overload conditions over 250Wrms. At full drive level approaching clipping, the electrical attenuation to the protected HF driver is -4.5dB. In every way, Eminenece px crossovers are a technically superior product.

* 2-Way * Crossover Frequency 1.6kHz * Slope 12dB/octave LP - 18dB/octave HP Butterworth * Impedance 8ohms * Power Handling 400Wrms

PX SERIES:pxb:3k5 PROFESSIONAL CROSSOVERS

Designed to work in high-power cabinets, px crossovers are technically superior passive filters available as board-only or complete with fitted hardware for a smart, economical 'factory-fit' finish.

Designed and built for Eminence, px crossovers feature advanced circuit design to both preserve the crossover and your HF drivers.

A common crossover problem in L-PAD failure brought about by winding burnout when maximum attenuation is prolonged.

Full attenuation concentrates the maximum voltage drop in a small winding area - a potentially damaging state even with high-power L-PAD devices.

In px crossovers, current is limited when the HF level control is set to "0" on its scale (max. -9dB attenuation). A secondary benefit of the design is to form a voltage divider across the HF driver. The High-Pass Protection uses custom-buitl aerospcae lamps as positive temperature coefficient series varistors.

The tungsten filaments effectively track the program material, dynamically maintaining a safe maximum current level to the HF driver without introducing distortion. This circuitry provides smooth 3:1 analog compression during input overload conditions over 250Wrms. At full drive level approaching clipping, the electrical attenuation to the protected HF driver is -4.5dB. In every way, Eminence px crossovers are a technically superior product.

* High-Pass * Crossover Frequency 3.5kHz * 18dB/octave Butterworth * Impedance 8ohms * Power Handling 400Wrms